Home Studio: Bugged By Audio Distortion? Check Your Audio Gain Staging … Huh? by Jamie Muffett
HOME STUDIO
If You’re Bugged By Audio Distortion,
Check Your Audio Gain Staging … Huh?
January 17, 2014
By Jamie Muffett
Voice Actor & Audio Engineer
Audio gain staging. “Huh?” you ask.
Actually, it’s a pretty simple concept and crucial to a clear and un-distorted sound.
Gain
staging simply refers to how you control the level at every stage of
the sound’s journey from mouth to finished article.
If there is
excessive gain at any stage of the process, the audio will distort and
fundamentally suffer, and it is not always obvious where this is
happening.
AFFECTS ALL SOUND
Phantom distortion can be an infuriating problem, so it is
best to try and eliminate it from the outset.
Here is an analogy: I often think of audio processing as similar to
water flow. Think of a water company supplying water to a neighborhood –
water flows from the reservoir and goes through many series of pipes. If
any of these pipes were to leak, or worse, somehow contaminate the
water, everything below that stage would be affected. And then, however well
maintained and leak-free the pipes further down the chain were, the
water has already been affected.
This is the same for audio, audio distortion and gain staging.
WHERE IT HAPPENS …
Here are potential places where this can happen. If you do have audio distortion, you can systematically rule
out each of these stages in your system, to discover whether gain
staging is or isn’t the problem for you.
1. YOUR MICROPHONE
So to start with, it is important that the microphone itself isn’t
being overloaded.
Some microphones can take high SPL’s (sound pressure
levels), most dynamic microphones won’t have this problem, and a lot of
condenser, tube and ribbons are designed to withstand levels associated
with the human voice.
However, some have such a sensitivity that you
need to be a certain distance or angle from them, and/or use some kind
of pop shield or screen.
More fully-featured mics will have a pad switch that turns the sensitivity (level) down in multiple db increments.
This is your first port of call when checking for distortion.
Take additional hardware and software out of the chain (compression/gating/EQ) when
you check for this, and make sure your pre amp is relatively low.
Disable any plugins and processing, then turn your playback volume up to
listen for any distortion.
2. CHECK THE PRE AMP
Again, disable any hardware or software
dynamics or EQ, turn down the gain on your pre amp, and slowly increase it
to a healthy level (use your meters on the pre and your DAW.
Never go
above -10db input level.
If your pre has a line level or trim output, you
can also play with that and balance it with with the gain for a non
distorted and healthy signal.
3. CHECK OTHER HARDWARE
Check any hardware between your pre and the computer, check
meters, LED’s or however else the device is measuring level.
For example, if I
compress audio on the way in, I never use more than -5db of
compression, and ensure a slow attack time to avoid chopping any
transients.
Check input and output levels of EQ units, as this can be
something that goes under the radar (remember that EQ itself is the
process of increasing or decreasing gain, just at specific frequencies).
4. WATCH INPUT METERS
Once your audio is in the system, check the input meters within your DAW (digital audio workstation), or, your recording/edting software.
The levels should be WELL
under 0db at the peak level on your master bus.
Also check the input and output of every plugin in your chain, on the
channel, any sub buses and on the master bus – and of course, the master
output level meter.
If you don’t hit
the red at any of these stages, and you maintain a decent level
throughout, you will not have any gain staging issues, and good for you!
———————————————-
ABOUT JAMIE
Jamie Muffett is British voice over artist and audio engineer who
lives in New York City. His client list includes Yahoo!,
Coca-Cola, McDonald’s, HP, National Geographic, Ebay and
Samsung.
Email: info@jamiemuffett.com
Web:www.yourbritvoice.com

Jamie – EXCELLENT article! Many thanks for this clear and helpful guide to tracking down distortion problems in finished audio.